?

단축키

이전 문서

다음 문서

+ - Up Down Comment Print
?

단축키

이전 문서

다음 문서

+ - Up Down Comment Print

http://link.springer.com/article/10.1007%2Fs12206-014-1131-1

 

Influence of repetitive pulsed laser irradiation on the surface characteristics of an aluminum alloy in the melting regime

  • Sungho Choi
  • , Kyung-Young Jhang 

Abstract

We have investigated the influence of repetitive near-infrared (NIR) pulsed laser shots in the melting regime on the surface characteristics of an aluminum 6061-T6 alloy. Characteristics of interest include surface morphology, surface roughness, and surface hardness in the melted zone as well as the size of the melted zone. For this study, the proper pulse energy for inducing surface melting at one shot is selected using numerical simulations that calculate the variation in temperature at the laser beam spot for various input pulse energies in order to find the proper pulse energy for raising the temperature to the melting point. In this study, 130 mJ was selected as the input energy for a Nd:YAG laser pulse with a duration of 5 ns. The size of the melted zone measured using optical microscopy (OM) increased logarithmically with an increasing shot number. The surface morphology observed by scanning electron microscopy (SEM) clearly showed a re-solidified microstructure evolution after surface melting. The surface roughness and hardness were measured by atomic force microscopy (AFM) and nano-indentation, respectively. The surface roughness showed almost no variation due to the surface texturing after laser shots over 10. The hardness inside the melted zone was lower than that outside the zone because the β″ phase was transformed to a β phase or dissolved into a matrix.

Keywords

Near-infrared pulsed laser Aluminum alloy Melting Surface morphology Surface roughness Surface hardness

분류 제목 조회 수
International Thermal damages on the surface of a silicon wafer induced by a near-infrared laser   637025
International Analysis of the influence of surface roughness on measurement of ultrasonic nonlinearity parameter using contact-type transducer   503747
International Absolute Measurement and Relative Measurement of Ultrasonic Nonlinear Parameter   302766
International Influence of repetitive pulsed laser irradiation on the surface characteristics of an aluminum alloy in the melting regime   279914
International Real-time detection of surface cracks on silicon wafers during laser beam irradiation   249344
International Non-contact Measurement of Elastic Modulus by using Laser Ultrasonic   231787
International Assessment of Thermal Degradation by Cumulative Variation of Ultrasonic Nonlinear Parameter   207517
International Evaluation of Ultrasonic Nonlinear Characteristics in Heat-Treated Aluminum Alloy (Al-Mg-Si-Cu)   191728
International Surface characteristics of aluminum 6061-T6 subjected to Nd:YAG pulsed-laser irradiation   187317
International Non-contact Single-Mode Guided Wave Technique by the Combination of Wavelength-Matched Laser Generation and Angle-Matched Leak Wave Detection   183030
International Experimental Comparison of Nonlinear Parameters Obtained from Absolute Measurement and Relative Measurement   167855
International Finite Difference Method Analysis of Ultrasonic Nonlinearity in Partially Degraded Material   160087
International Non-Contact Evaluation of Acoustic Nonlinearity of a Laser-Generated Surface Wave in a Plastically Deformed Aluminum Alloy  image 159949
International Fatigue-induced microdamage characterization of stainless steel 316L using innovative nonlinear acoustics   148121
International Demonstration of Disturbance Propagation and Amplification in Car-Following Situation for Enhancement of Vehicle Platoon System   147462
International Single-mode guided wave technique using ring-arrayed laser beam for thin-tube inspection   144282
International Comparison of Ultrasonic Nonlinear Parameters Measured by PZT and LiNbO3 Transducers   140132
International Crack Detection in Single-Crystalline Silicon Wafer Using Laser Generated Lamb Wave   139239
International Relationship between Second- and Third-order Acoustic Nonlinear Parameters in Relative Measurement  image 138433
International "Acoustic Nonlinearity of Surface Wave in a Fatigued Aluminum Alloy Specimen "   135660
Board Pagination ‹ Prev 1 2 3 4 5 6 Next ›
/ 6
Designed by hikaru100

나눔글꼴 설치 안내


이 PC에는 나눔글꼴이 설치되어 있지 않습니다.

이 사이트를 나눔글꼴로 보기 위해서는
나눔글꼴을 설치해야 합니다.

설치 취소

SketchBook5,스케치북5

SketchBook5,스케치북5

SketchBook5,스케치북5

SketchBook5,스케치북5

ISNDE Laboratory
203-2,Engineering Center Annex
Hanyang University,
222 Wangsimni-ro, Seongdong-gu
Seoul 04763, Korea
04763 서울특별시 성동구 왕십리로 222
한양대학교 공업센터 별관 203-2호
지능계측 및 비파괴평가 연구실
Tel: 02 - 2220 - 4220
Fax: 02 - 2299 - 7207