In situ detection of laser-induced slip initiation on the silicon wafer surface
http://www.ncbi.nlm.nih.gov/pubmed/25121706
In situ detection of laser-induced slip initiation on the silicon wafer surface.
Abstract
We propose a real-time in situ method to detect slip initiation on the surface of silicon wafers during high-power laser beam irradiation. In this method, light is collected from the surface of a silicon wafer subjected to laser irradiation. When the slip is initiated, it strongly scatters the laser beam, allowing detection of the time of the slip initiation based on the resulting sudden increase in the scattering signal. To demonstrate the performance of this method, a silicon wafer specimen was illuminated by a near-infrared continuous-wave fiber laser beam (of wavelength 1070 nm) at four different laser powers, and the scattered light was detected. The scattering signal increased suddenly at the time of slip initiation. To confirm the occurrence of slip, the surface morphologies of the silicon specimens after laser irradiation were analyzed using an optical microscope; surface slips were observed only in the specimens for which the sudden increase in scattering had been detected. Thus, the proposed method is shown to be very effective for the real-time in situ detection of surface slip initiation induced by high-power laser beam irradiation on silicon wafers.
-
Full-range stress–strain curve estimation of aluminum alloys using machine learning-aided ultrasound
Date2024.03.19 CategoryInternational Views40 -
Nondestructive Inspection of Directed Energy Deposited Components Using Scanning Acoustic Microscopy with Metalworking Fluids
Date2024.03.19 CategoryInternational Views31 -
Nondestructive Inspection of Cylindrical Components Repaired Via Directed Energy Deposition Using Scanning Acoustic Microscopy with Metal Lubricants
Date2024.03.19 CategoryInternational Views194 -
Plastic properties estimation of aluminum alloys using machine learning of ultrasonic and eddy current data
Date2024.03.19 CategoryInternational Views67 -
Calibration method using a narrowband signal for measurement of the acoustic nonlinearity parameter
Date2024.03.19 CategoryInternational Views30 -
Comparisons of second- and third-order ultrasonic nonlinearity parameters measured using through-transmission and pulse-echo methods
Date2022.11.15 CategoryInternational Views2467 -
In-situ and Layer-by-layer Grain Size Estimation of Additively Manufactured Metal Components using Femtosecond Laser Ultrasonic Technique (Submitted)
Date2022.02.21 CategoryInternational Views953 -
Microstructural Characterization of Additively Manufactured Metal Components Using Linear and Nonlinear Ultrasonic Techniques
Date2022.02.21 CategoryInternational Views1273 -
Tensile properties evaluation of additively manufactured Ti-6Al-4V/yttria-stabilized zirconia composite using absolute nonlinear-ultrasonic technique (Submitted)
Date2022.02.21 CategoryInternational Views12461 -
Generation and Measurement of Gigahertz Ultrasonic Waves in Additively Manufactured Thin Metal Components using Femtosecond Laser and Application to In-situ Grain size Monitoring (Submitted)
Date2022.02.21 CategoryInternational Views26218 -
Nondestructive evaluation of micro-oxide inclusions in additively manufactured metal parts using nonlinear ultrasonic technique
Date2021.08.25 CategoryInternational Views20091 -
Mechanical properties estimation of additively manufactured metal components using femtosecond laser ultrasonics and laser polishing
Date2021.08.25 CategoryInternational Views28937 -
Experimental Verification of Contact Acoustic Nonlinearity at Rough Contact Interfaces
Date2021.08.25 CategoryInternational Views49944 -
Compensation of a Second Harmonic Wave Included in an Incident Ultrasonic Wave for the Precise Measurement of the Acoustic Nonlinearity Parameter
Date2021.08.25 CategoryInternational Views45565 -
Measurement of Absolute Acoustic Nonlinearity Parameter Using Laser-Ultrasonic Detection
Date2021.08.25 CategoryInternational Views43242 -
Rapid Molecular Diagnostic Sensor Based on Ball-Lensed Optical Fibers
Date2021.08.25 CategoryInternational Views36401 -
Porosity Evaluation of Additively Manufactured Components Using Deep Learning‑based Ultrasonic Nondestructive Testing (Editor's pick)
Date2021.08.25 CategoryInternational Views12111 -
Deep Learning-Based Ultrasonic Testing to Evaluate the Porosity of Additively Manufactured Parts with Rough Surfaces
Date2021.08.25 CategoryInternational Views21486 -
Analysis of the influence of surface roughness on measurement of ultrasonic nonlinearity parameter using contact-type transducer
Date2021.08.25 CategoryInternational Views505806 -
Indirect Method for Measuring Absolute Acoustic Nonlinearity Parameter Using Surface Acoustic Waves with a Fully Non-Contact Laser-Ultrasonic Technique
Date2021.08.25 CategoryInternational Views31722